How to Turn a Cane Backed Chair into a Parsons Chair

Hello again! Going along with my quest for the perfect Dining Room Set I needed to find something to do with the cane backed chairs that came with my dining table.  I'm really not a fan of cane backed chairs, so I came across a blog post about how to turn them into Parsons Chairs! How wonderful!  You can view her original post here, but if you don't want to click, here's a tutorial on how I did mine.

First, here are the original chairs that we're dealing with.  There are 4 of them.

 

During one of the later steps, I discovered that these were built in the 1920s!!  And yes, that is the original fabric...it basically fell apart in my hands it was so old.

 

And here is the finished product!!

 

 

Quite a difference huh?! Now on to the tutorial!!

 

Supplies:

Upholstery Fabric

This was a LARGE chair, and I have 4 of them to do, so I bought 6 yards of fabric.  The people at the fabric store really were a big help with trying to figure out how much I'd need! NOTE: I did not use all 6 yards to complete these chairs.  I'm not really sure how much I did use though...there seems to be a lot left...hmm, curtains? :)

Spray Paint (I chose black)

A coarse sand block or sand paper

A fine sand block or sand paper

Wood stain

Q-Tips

Several Rags or old T-Shirts

Screwdriver

Staple Gun

Paper (I used newspaper)

Spray Adhesive

Cardboard

Masking Tape

Gorilla Glue (or really strong all purpose glue)

NOTE: Elmer's school glue will not work

Pillow

Measuring Tape

Scissors

 

How To:

These first few steps don't have pictures, because I did most of this before I started blogging. Sorry. :)

First take your screwdriver and remove the seat from your chair.  You will need to remove the old fabric from the seat of your chair if it is really old like mine. In most cases though, you can just recover the new fabric onto the existing seat cushion.  My fabric is very silky and somewhat thin, so I didn't want the old textures coming through.

 

NOTE: It is really important to use upholstery fabric.  This is something that you will be sitting on, not just something to look pretty. You want it to stand up the test of time and last longer than 1 use.  If you have children and they will be using these chairs...two words...SCOTCH GUARD. Actually, it's not a bad idea even if you don't have children, or if they will not be using it.  My husband spilled Cherry Coke on our chair about a week after I finished it.  It took him 4 hours to get it clean.

 

Then use your seat as a template to cut out your fabric for your seat cushion.  Make sure to add 2 - 3 inches around your cushion so that it will wrap around and secure easily to the underside of the seat.  I cut a very large square.

 

Starting at the middle of one side, attach the new fabric with a staple gun to the underside of your seat.  After the first side is in place, don't hesitate to pull and stretch the fabric across the seat before your staple.  Otherwise, you will have a very wrinkled looking seat cushion.  Set your finished seat aside.

 

So now, your chair should look like so:

 

 

Next take your coarse sand block/paper and sand off the "gloss" from your chair.  You only need to sand off the bottom half of your chair. From the "waist" down if you will. Make sure you sand off the back of the chair below the cane as well.  This will show in the finished product.

 

 

You do not need to take it all the way down to the bare wood, just take the gloss finish off.  This will let the paint actually adhere to your chair.  When all is sanded, make sure you wipe it down with a DAMP rag.  You want to make sure you get all the little sand bits off the chair.  It will ruin your finish if you don't.

 

 

After you've wiped the chair down, spray paint it in your color choice. Again, you will only need to paint about halfway up. No need to paint the top of the chair because you are going to cover it with material anyway.

 

 

I used Rustoleum Spray Enamel in Black Satin finish for my chairs.  I don't like a lot of gloss, but there are so many choices and finishes...get creative!!

 

All painted!

 

 

Don't worry about painting the inside of the chair because your seat will cover it.  You do need to paint the top of the seat portion though, in case your cushion doesn't cover all the edges. Make sure to let your paint dry.  My particular paint takes 24 hours to dry completely, so this whole process takes a few days.

 

***If you want that ever popular Pottery Barn look, then the next few steps are for you...if not, just skip ahead to the assembly steps!!

 

To distress your furniture, you will need your fine sand block/paper.  Give your entire chair another sanding all over.  Make sure to concentrate on the edges and creases to "take off" the paint from these areas.  The more you sand, the more worn it will look, again, this is custom so have at it!!

 

 

I don't like much distressing, so this doesn't take long for me.

 

 

Then wipe your chair down again with your DAMP rag.  You don't want fine colored dust all over you or your guests' clothing. :) 

 

Then take your wood stain and a Q-Tip. Dip the Q-Tip into the stain and "paint" all of the exposed areas that you just sanded off.  If you like, you can also take a clean rag and stain the whole chair by dipping the rag in the stain and applying it directly to the entire chair. Painted portion only of course. I used Minwax Wood Stain in Provincial.

 

 

 

Make sure to let the stain sit for a couple of minutes, then wipe it off with a DRY rag.  This will remove any excess stain, again, saving your clothing from ruin.

 

Here is the chair stained and finished.

 

 

Notice how the stain colored the wood to create less of a contrast. 

Yet, it still looks worn and expensive! :)

Let this stain dry another 24 hours or so and then you'll be ready to assemble your chair!!

 

***If you skipped ahead, stop now! This is information you will need to finish your chair. :)

 

You'll need to make a template with paper of the back of your chair.  This will help you to know the pattern to cut out your cardboard.  After you've created your template, trace it onto your cardboard. I used a shipping box that we had in our recycle area.  You will most likely need to break down a box to get a large enough surface to trace onto. There are a couple of "seams" in my box, but it won't show when you're finished.

 

 

Then cut out your cardboard "back." Next lay it on your fabric again to see how much you will need to cover the cardboard.  Again, make sure you leave about 2 - 3 inches around the perimeter so that it will attach well.  Cut out your fabric.

 

You can use spray adhesive or a small amount of glue on the front of your cardboard where the fabric will go.  Place the cardboard in the middle and press to adhere.  Wrap the piece of fabric around the cardboard back and secure with masking tape. Set this "back" aside with your seat.

 

Then, attach your pillow to the top of your chair with the staple gun.  I did cut the pillow at the top so that I could arrange the stuffing as I liked.  I wanted to make sure there would be enough fluff around the top pieces of wood.  Again, really pull on this pillow so it is attached well.  You want to staple it into the wood of your chair. 

 

 

 

Now for the fun part! Measure from the back of your chair by the cane all the way around the pillow to the other side/back of your chair by the cane. Add another 2 inches to this measurement.  This will give you the width of your material to cover the top of your chair.  For the length, measure from the front under your pillow (where the seat will sit) to around the top and under the wood, again by the cane.  Add another 2 inches.  Then you have how much you will need to cover this top.  Cut out your fabric.

 

Lay your fabric on your chair around your pillow and line it up where it is even on both sides.  Starting at the top center, staple the fabric under the top part of the wood next to the cane.  Do not continue the rest of the top yet, this is just to stabilize your fabric as you do the next step.

 

Then pull and staple your sides next.  Leave about an inch or so at the bottom of both sides so that you can finish the bottom easily.  Really make sure you pull your fabric before you staple.  It will make a difference in the look of your chair!!

 

 Continue to attach the top of your fabric. You can create a fun design, or just gather and staple. I decided to create a nice pleat in mine. I think it looks elegant. It's kind of like wrapping a present.

 

Now staple the bottom of your fabric.  Before you staple this, fold the "hem" under about 1/2 of an inch so that you will not have any stray strings or unraveling going on.  Again, pull and staple well.

Here is what it should look like now!!

 

 

Now take the "back" of your chair (remember your upholstered cardboard) and glue it to the cane part of your chair.  Make sure the edges are secure as well so that it doesn't separate from your chair.

Next take your seat and reattach it to your chair with the screws you took out before.  Don't worry about making holes in your fabric, because the screws will do that for you.  Make sure you tighten it well. 

 

 

Voila!! You are done!!

 

 

 

What do you think?!?!  Sit in it! Feel the softness of all your hard work!  Now how amazing is it that you just created a chair that easily would sell for a minimum of $80 brand new for no where near that?!  I got my fabric on sale at our local store and each chair cost me (with paint and all supplies) about $25 - $30 to make!!

 

I think it looks great at my dining room table!!  Leave a comment on where you will put yours!

Spray Paint Refinishing

Good afternoon!  You may remember the quest I'm in for creating my perfect mis-matched Dining Room Set.  If not, click here to see that post.

This is the promised tutorial of how I refinished the garage sale chairs.  It takes several days to finish each chair, but it is oh so worth it when it's done!! AND it's exactly what I want!! You can do it too!  I'll tell you how - -

Supplies:

Wooden Chair

Spray Paint in your color choice (I like black)

Coarse Sandpaper or Electric Sander Tool thing

Fine Sandpaper or Sand block

Wood Stain

Q-Tips

Rag or old T-Shirt

 

How To:

First, start with a wooden chair.  Any chair will do as long as you like it or need it refinished.  Here's one of my finds from a garage sale. I paid $2 for it!

 

 

Notice this one is painted white? I don't want it white...I want it black.  This one took a little longer in this next step, but the process is still the same.  I will warn you...BEWARE of already painted chairs.  Stained chairs are MUCH easier to refinish and don't take as long!!

 

Next, you will need to take your coarse sandpaper/block or electric sander and completely sand off the existing finish. You only need to make sure that the gloss is gone, you don't need to take it completely to the bare wood...unless the chair is already painted. (See note above)

 

 

Once the chair is "unfinished," you need to wipe it down.  Use a damp rag or old T-shirt to do this.  It is very important to get all the sand and dust off the chair.  Otherwise, you will get a coarse look to your chair and it will take step one to get it looking better again.

 

Now that the chair is wiped off and bald...spray paint it.  Make sure you get in all the nooks and crannies of the chair.  The paint I used was Rustoleum Black Satin Enamel.  It is important to get the Enamel kind because it will wear better.  Since this is a chair we will use often, I wanted it to stand the test of time.

 

 

This particular spray paint needs 24 hours to dry completely, so watch some tv, dream about your new chair...basically whatever you can think of to pass the time.  When the coat is done, your chair should look like so:

 

Mine is glossy because I didn't let it dry before taking the picture.  The satin finish will dry to a smoother texture and look.  Next step is to take your fine sandpaper/block and sand the chair down again.  This will smooth out all the rough places from the previous sanding and again, help the chair to wear better.  This time, you don't need to spend as much time sanding.  Just a quick once over is fine.

 

Now to "distress" your chair, spend more time around the edges and angles of your chair. 

 

 

Be creative.  The more you sand, the more "worn" your chair will look.  I don't like a lot of distressing to it, but I do like some, so this doesn't take too long for me.  Really think about where the chair would naturally wear down.  Tops, seat, edges...etc. This is what it will look like when you're done.

 

 

Notice the "I've-had-this-chair-for-years-and-my-children-have-worn-it-out-antique look?" 

 

Make sure to wipe the chair down again because you don't want fine black dust all over your clothes or the clothes of anyone who sits in the chair.  Again, using a damp rag will work best.

 

 

Then take your Q-Tip and dip it in the stain of your choice.  I used Minwax Provincial Stain.  It's the same stain that we have on our floors, so I thought that would be a nice touch. Kind of matching, but no one would really notice.  Your choice of stain WILL make a difference in the look of your chair, so choose what you like, not just what is available. 

 

 

 Run your dipped Q-Tip over all your distressed/exposed parts.  Make sure to stain ALL your areas, otherwise, you will have a non uniform look.  After you let the stain sit for a couple of minutes or so, make sure to wipe off the stain with a DRY rag.  Again, not doing so could result in ruined clothing. If you want, you could use your rag and stain the whole chair again, but this is the quicker way. 

 

 

Let the stain dry and then voila! You have a finished chair!

 

 

If you like, you could add another step to further protect your furniture from damage.  Minwax makes a polyurethane coat in a spray as well.  After you have completed the staining process, give a once over with this clear coat.  It will just protect your chair from damage from daily use.  I'm contemplating doing this with the chairs the kids will be using.  It will also help with clean up from spills...etc as it will withstand soap and water cleaning well.

 

I hope yours will turn out well.  It takes me about 3 days to finish a chair with all my little boys running around and wanting to eat and all. :) I do like the way they look around my table though!